Why is My Dishwasher Leaking?

Getting up in the morning to find an ominous puddle on the floor is never the best to start the day.

Fortunately, most simple sources of dishwasher leaks are comparatively simple to diagnose and mend by yourself. Meaning you might not have to wash the dishes by hand that much, call an engineer or need to pay a high call-out charge.

So, find the manual if you can, get a towel to clean up the mess and so get something clean up any further leaks and so see if you can’t fix the problem. If you can’t call us for local dishwasher repair.

Commonly Seen Causes of Dishwasher Faults as well as How to Fix Them

A lot of the most everyday causes of dishwasher leaks are not really a result of a dishwasher fault . Prior to starting preparing yourself for an engineering task and watching endless online tutorials there are a couple of things you can take a look at first.

  1. Check to find out if your dishwasher is level. If the dishwasher is not level water can easily puddle and so spill out without there being anything that needs to be resolved or replaced.
  2. Investigate you are using the correct soap. You might have seen this with your washer. Too much soap or using the wrong type may result in to too many soap suds, the soap suds deluge and you get a spill.
  3. Investigate your dishwasher door fully closes. If there’s a gap there may be a blockage, or you could need to adjust the hinge or the locking mechanism.
  4. Investigate the filter at the base of the machine for any easy to see obstructions as if your dishwasher isn’t draining properly this will cause it to fill too much and spill.

Once you have ruled out these possible causes it’s time to roll up your sleeves and begin a thorough check.

To make your life easier start with the door as well as test for any visible damage within of the machine prior to moving on to the underside. If you are able to find and so mend the problem without pulling out the dishwasher you’ll save yourself a lot of hassle.

And make sure you disconnect the appliance first by either unplugging it or turning off the circuit breaker for the dishwasher.

Door Seal

The most everyday place for a dishwasher to leak is around the door, luckily it is likewise one of the simplest issues to fix.

If the leak is occasional the issue could be as simple as a big pan or another object putting pressure into the door thus preventing the door from sealing fully.

Else-ways the door gasket could have come out of place or become damaged.

Examine the door gasket and investigate for any brittleness, mineral deposits or other gunk, or any parts where the gasket has separated from the door.

Taking off the gasket and allowing it a comprehensive clean can improve the situation in some instances or you may have to purchase a new seal and change it.

Water Inlet Valve (Solenoid Fill Valve)

The inlet valve can also be a everyday issue. This is generally found under the machine therefore you will most likely need to take off the kick plate and also may have to remove the door cover.

The inlet valve opens and also closes to allow water into the dishwasher at different parts of the program. The inlet valve may be damaged, demonstrated by a slow drip, or it might be broken and not operating fully while the dishwasher is running.

In the case that the water inlet valve doesn’t close properly this can mean that the dishwasher overfills, causing a leak.

Often these valves can’t be repaired unless it is only the rubber gasket that is broken, thus the whole component would need to be replaced.

Leaking Hoses

Hoses are needed to supply, drain and recirculate water within the cycle.

Two complications might develop where hoses are involved.

  1. The seals could break or the contact points may come loose so it’s worth checking all the connections first.
  2. The alternative fault than could easily happen over time is that hoses can become degraded or cracked.

If you can determine that the leak is coming from a hose this should be simple to replace and spare hoses are readily available.

Pumps and Seals

You can visually investigate the seals that are part of the water pumps or motor to determine if there is a leakage as well as change them if that’s the case.

The Float Switch

Either the float or the float switch could be broken resulting in the dishwasher overfilling.

A working float will lift up as the water level goes up until the optimum or highest water level is attained. The tail of the float would then operate the switch. A blockage or breakage could be causing your issues.

Testing the switch will require electrical equipment but it could be clearly damaged in which case getting a new one should fix the problem.

Other Parts that Could Cause Leakage

A cracked wash arm or support can force water under the door resulting in leakage. This will likewise often result in your dishes not being cleaned as effectively as they should.

Broken or faulty lines may also result in this fault as may a cracked pump cap if your dishwasher has one.

The motor shaft gasket may have degraded causing leakage. This will generally show as a puddle coming from the underside of the appliance.

Top Tips to Sort Out Your Machine

  1. Save money by checking the gasket instead of the entire component. In most instances, you can acquire the seal without the rest of the part which saves you having to change the entire component.
  2. Check the simple fixes before you get more complicated. There’s no point pulling the entire machine out if the problem is the soap.
  3. Photograph your progress. This can assist you to reverse the process, describe the part you need to a sales person, and identify the problem to an engineer if needed.
  4. Stay safe. Water and electricity do not mix so unplug the machine first.
  5. If you’re not sure get in a repair person.

The Next Steps You Should Take If Your Trouble Shooting Doesn’t Identify or Resolve the Leakage

If the root of the issue is still a mystery the next step you can take is to pull the dishwasher away from the wall to get a clearer view of the underneath it and also add water to the tub to see whether the leakage becomes visible.

If this doesn’t shed any light your dishwasher may only show a leakage when it’s running. If this is the case, you should hire a appliance repair person to diagnose and resolve the leak as there are safety risks of running the dishwasher with electrical parts exposed.

More Dishwasher Problems: